CISCO\H3C\HUAWEI等新旧网络产品回收

回收热线\微信号:13316580697
回收QQ:2604854556

产品分类

联系我们

深圳市绿思科技有限公司

地址:深圳市龙岗区龙岗天安数码城4栋A座609

联系人:罗先生   QQ:2604854556
电话/微信号:13316580697

传真:0755 22141929

http://www.2ciscow.com

腾  讯


新  浪

回收AS5300语音网关系列

首页  »  产品展示  »  回收CISCO网关及其它  »  回收AS5300语音网关系列

CISCO AS5300
发布时间:2012-2-28 15:39:38 点击量:
CISCO AS5300产品简介 

Follow these steps in order to recover your password:Attach a terminal or PC with terminal emulation to the console port of the router.  CISCO AS5300

Use these terminal settings:

9600 baud rate

  • No parity   CISCO AS5300

  • 8 data bits

  • 1 stop bit

  • No flow control

Refer to these documents for information on how to cable and connect a terminal to the console port or the AUX port:

  • Note: The configuration register is usually set to 0x2102 or 0x102. If you can no longer access the router (because of a lost login or TACACS password), you can safely assume that your configuration register is set to 0x2102.

  1. Use the power switch in order to turn off the router, and then turn the router back on.

    Important Notes:

    • In order to simulate this step on a Cisco 6400, pull out and then plug in the Node Route Processor (NRP) or Node Switch Processor (NSP) card.

    • In order to simulate this step on a Cisco 6x00 with NI-2, pull out and then plug in the NI-2 card.

  2. Press Break on the terminal keyboard within 60 seconds of power up in order to put the router into ROMMON.CISCO AS5300

  3. Type confreg 0x2142 at therommon 1>prompt in order to boot from Flash.

    This step bypasses the startup configuration where the passwords are stored.

  4. Type reset at therommon 2>prompt.CISCO AS5300

    The router reboots, but ignores the saved configuration.

  5. Type no after each setup question, or press Ctrl-C in order to skip the initial setup procedure.

  6. Type enable at theRouter>prompt. CISCO AS5300

    You are in enable mode and should see theRouter#prompt.

  7. Type configure memory or copy startup-config running-config in order to copy the nonvolatile RAM (NVRAM) into memory.

    Important: Do not type copy running-config startup-config or write. These commands erase your startup configuration.

  8. Type show running-config. CISCO AS5300

    The show running-config command shows the configuration of the router. In this configuration, the shutdown command appears under all interfaces, which indicates all interfaces are currently shut down. In addition, the passwords (enable password, enable secret, vty, console passwords) are in either an encrypted or unencrypted format. You can reuse unencrypted passwords. You must change encrypted passwords to a new password.

  9. Type configure terminal. CISCO AS5300

    Thehostname(config)#prompt appears.

  10. Type enable secret <password> in order to change the enable secret password. For example:

    hostname(config)#enable secret cisco  CISCO AS5300
  11. Issue the no shutdown command on every interface that you use.

    If you issue a show ip interface brief command, every interface that you want to use should display up up.

  12. Type config-register <configuration_register_setting>. Where configuration_register_setting is either the value you recorded in step 2 or 0x2102 . For example:

    hostname(config)#config-register 0x2102  
  13. Press Ctrl-z or end in order to leave the configuration mode.

    Thehostname#prompt appears.

  14. Type write memory or copy running-config startup-config in order to commit the changes.

    CISCO AS5300

 

上一条:AS5350XM 思科网关 | 下一条:无下一篇

版权所有 Copyright © 2009-2011 All rights reserved. CISCO\H3C\HUAWEI等新旧网络产品回收
地址:深圳市龙岗区龙岗天安数码城4栋A座609 http://www.2ciscow.com 咨询热线:13316580697 联系人:罗先生 企业邮箱:cisco@2ciscow.com
粤ICP备11090912号-1

在线客服
  • 采购部

    采购经理

    点击这里给我发消息
  • 销售部

    销售经理

    点击这里给我发消息

    销售经理

    点击这里给我发消息
  • 技术部

    技术经理

    点击这里给我发消息

绿思科技微信公众号

网络设备回收